Rules for OverpressureProtectionSECTION XIIIASME BPVC.XIII-20232023 ASME...
ð23PART KDDESIGN REQUIREMENTSARTICLE KD-1GENERALKD-100 SCOPEa The...
ASME BPVC.VIII.2-2023Division 2Alternative RulesSECTION VIIIRules for...
SECTION VIIIRules for Construction of Pressure VesselsASME...
Recommended Guidelinesfor the Care of Power BoilersSECTION VIIASME...
Viewed products
ASME B18.18.2-2009...
AS IEC 60601.1.10:2017...
ASME PTC 70-2009 (R2019) Ramp Rates standard by ASME International, 04/15/2009 Full Description This code provides the procedures, direction, and guidance for the accurate determination, via testing, of the maximum repeatable load change ramp rate, startup load change...
ASME PCC-2-2008 Repair of Pressure Equipment and Piping standard by ASME International, 04/07/2009 Full Description This Standard provides methods for repair of equipment and piping within the scope of ASME Pressure Technology Codes and Standards after it has been placed...
ASME B31.12-2008 Hydrogen Piping and Pipelines standard by ASME International, 03/31/2009 Full Description This Code is applicable to piping in gaseous and liquid hydrogen service and to pipelines in gaseous hydrogen service. This Code is applicable up to and including...
ASME B18.2.4.5M-2008 [ Withdrawn ] Metric Hex Jam Nuts standard by ASME International, 03/31/2009 Full Description This standard covers the general and dimensional data for metric hex jam nuts recognized as American National Standard. The inclusion of...
ASME Y14.5-2009 Dimensioning and Tolerancing standard by ASME International, 03/27/2009 Full Description This standard establishes uniform practices for stating and interpreting dimensioning, tolerancing, and related requirements for use on engineering drawings and in...
ASME STP-NU-019-1 Verification of Allowable Stresses in ASME Section III Subsection NH for Grade 91 Steel standard by ASME International, 03/19/2009 Full Description This document is the outcome derived from an agreement between the U.S. Department of Energy (DOE) and...
ASME B20.1-2009 Safety Standards for Conveyors and Related Equipment standard by ASME International, 03/16/2009 Full Description B20.1 applies to the design, construction, installation, maintenance, inspection, and operation of conveyors and conveying systems in relation...
ASME STP-PT-023 Guidelines for In-Service Inspection of Composite Pressure Vessels standard by ASME International, 02/23/2009 Full Description The purpose of this document is to provide recommendations for the procedures to be used for the inserviceinspection of...
ASME PTC 4.4-2008 (R2013) Gas Turbine Heat Recovery Steam Generators standard by ASME International, 01/30/2009 Full Description The object of this Code is to establish procedures for conducting performance tests of Heat Recovery Steam Generators (HRSGs) used to recover...
ASME STP-PT-025 Extended Fatigue Exemption Rules for Low CR Alloys into the Time-Dependent Range for Section VIII Division 2 Construction standard by ASME International, 01/29/2009 Full Description A number of alloys have applications slightly into the creep range that...
ASME STP-PT-028 Impact Testing Exemption Curves for Low Temperature Operation of Pressure Piping standard by ASME International, 01/29/2009 Full Description In this report - of high interest to the petrochemical industry - material models are examined for...
ASME STP-PT-027 Extended Low Chrome Steel Fatigue Rules standard by ASME International, 01/29/2009 Full Description In this report - of high interest to the petrochemical industry - material models are examined for hardening/softening and creep behavior based on...