Rules for OverpressureProtectionSECTION XIIIASME BPVC.XIII-20232023 ASME...
ð23PART KDDESIGN REQUIREMENTSARTICLE KD-1GENERALKD-100 SCOPEa The...
ASME BPVC.VIII.2-2023Division 2Alternative RulesSECTION VIIIRules for...
SECTION VIIIRules for Construction of Pressure VesselsASME...
Recommended Guidelinesfor the Care of Power BoilersSECTION VIIASME...
Viewed products
3A 10-04...
BS PD CEN/TS 17626:2021...
SAE AMS2245C Tolerances Titanium and Titanium Alloy Extruded Bars, Rods, and Shapes standard by SAE International, 09/14/2021 Full Description This specification covers established manufacturing tolerances applicable to titanium and titanium alloy extruded bars, rods,...
SAE SAE1007 Standard Practice for Habitability standard by SAE International, 09/14/2021 Full Description This Standard specifies the Habitability processes throughout planning, design, development, test, production, use and disposal of a system. Depending on contract...
SAE J2405_202109 Low-Permeation Fuel Fill and Vent Tube standard by SAE International, 09/14/2021 Full Description This SAE Standard covers the minimum requirements for a low-permeation tubing (100 g/m2/day or less) for use as a low pressure (14.5 kPa) liquid- or...
SAE ARP9114B Direct Ship Guidance for Aerospace Companies standard by SAE International, 09/14/2021 Full Description This document is limited to the aerospace industry, where an approved manufacturer requests a supplier to ship an article against the approved...
SAE AMS4474B Aluminum Alloy, Sheet and Plate 4.0Cu - 1.0Li - 0.40Mg - 0.35Ag - 0.13Zr (2195-T8) Solution Heat Treated, Cold Worked, and Artificially Aged standard by SAE International, 09/13/2021 Full Description This specification covers an aluminum alloy in the form...
SAE AMS6409F Steel, Bars, Forgings, Mechanical Tubing and Forging Stock 0.80Cr - 1.8Ni - 0.25Mo (0.38 - 0.43C) (SAE 4340) Special Aircraft Quality Cleanliness Normalized and Tempered standard by SAE International, 09/13/2021 Full Description This specification covers...
SAE AS85049/18D CONNECTOR ACCESSORIES, ELECTRICAL, BACKSHELL, ENVIRONMENTAL, STRAIGHT, RFI/EMI, CATEGORY 2B (FOR MIL-DTL-38999 SERIES III AND IV CONNECTORS) standard by SAE International, 09/10/2021
SAE J2984_202109 Chemical Identification of Transportation Batteries for Recycling standard by SAE International, 09/10/2021 Full Description The chemistry identification system is intended to support the proper and efficient recycling of rechargeable battery systems...
SAE J2198_202109 Glossary - Automatic Belt Tensioner standard by SAE International, 09/10/2021 Full Description This glossary was written to provide a consistent and uniform definition of terms used in describing an automatic belt tensioner as it applies to an...
SAE AS567L Safety Cable, Safety Wire, Key Washers, and Cotter Pins for Propulsion Systems, General Practices for Use of standard by SAE International, 09/10/2021 Full Description This SAE Aerospace Standard (AS) covers devices whose primary function is the retention...
SAE ARP4294A Data Formats and Practices for Life Cycle Cost Information (Stabilized: Sep 2021) standard by SAE International, 09/10/2021 Full Description This SAE Aerospace Recommended Practice (ARP)4294 is directed at life cycle cost (LCC) analysis of aerospace...
SAE ARP4293A Life Cycle Cost - Techniques and Applications (Stabilized: Sep 2021) standard by SAE International, 09/10/2021 Full Description This SAE Aerospace Recommended Practice (ARP) describes the concept of life cycle costing with emphasis on LCC techniques and...